Effect of microstructure inhomogeneity on mechanical properties of different zones in TA15 electron beam welded joints

The effects of microstructure inhomogeneity on the mechanical properties of different zones in TA15 electron beam welded joints were investigated using a micromechanics-based finite element method. Considering the indentation size effect, the mechanical properties for constituent phases of the base metal (BM) and heat affected zone (HAZ) were determined by the instrumented nano-indentation test. The macroscopic mechanical properties of BM and HAZ obtained from the tensile test agree well with the numerical results. The incompatible deformation between the constituent phases tends to localize along the softer primary phase α where failure usually initiates in form of localized plastic strain. Compared with the BM, the mechanical properties of constituent phases in the HAZ differ substantially, leading to more serious strain localization behavior.     

桩土复合路基静载试验改进方法研究

静载试验作为复合路基的一种重要检测手段而广泛应用,然而,在工程质量检测中,常出现检测结果与实际情况不符的情况,除人为操作因素外,垫层模拟过于简单是主要原因。借助引入弹性垫层,提出一种桩土复合路基静载试验改进方法。首先,基于数值模拟计算,建立复合路基桩土应力比n和桩土相对位移Δs、弹性垫层厚度h和弹性垫层模量E的函数关系;其次,通过模拟结果和路堤荷载结果对比,确定不同桩型复合路基静载试验中弹性垫层参数选择范围,最后,利用现场对比试验和实测结果,论证桩土复合路基静载试验改进方法的正确性和可靠性。     

Evaluation of back-calculated elastic moduli of unreinforced and geocell-reinforced unbound granular material from full-scale field tests

This paper presents a field-scale experimental track over a poor subgrade with an unreinforced section and a geocell-reinforced section subjected to in-situ performance tests. Plate load tests and Benkelman beam tests were carried out distributed in several unreinforced and reinforced layers. The objective was to: (1) examine the variability of the elastic modulus of unbound granular material (UGM) due the influence of its thickness and the presence of poor subgrade in its base, (2) evaluate the modulus improvement factor (MIF) generated by the geocell reinforcement in the UGM and (3) verify the most appropriate condition to apply the MIF to transport infrastructure design. The results showed that there is a significant influence of the thickness of the UGM layer on its elastic modulus when the layer is supported directly over a soft subgrade. The MIF values obtained in field suggest that its determination is mostly related to the UGM maximum elastic modulus rather than its decreased values (by virtue of poor subgrade or reduced thicknesses), and that the analytical formulation presented for MIF calculation has good predictive capability to be applied to pavement design.     

高能同步辐射光源低能束流输运线设计研究

高能同步辐射光源（HEPS）是计划在北京建造的发射度小于60 pm•rad的超低发射度光源。它由1台500 MeV直线加速器、1条500 MeV低能束流输运线、1台500 MeV～6 GeV的能量增强器、2条6 GeV的高能束流输运线、1台6 GeV的储存环以及同步辐射光束线和实验站组成。本文进行低能束流输运线的设计研究。低能束流输运线是连接直线加速器和增强器的束流传输线，在考虑建设布局限制的基础上，对两端的束流包络进行匹配，并将直线加速器产生的束流高效传输到增强器注入点。HEPS低能束流输运线设计时采用了功能分区的设计策略，设计有3个功能区，分别是消色散注入匹配区、光学参数匹配区、输出匹配区。为校正误差对束流的影响，HEPS低能束流输运线设置了8个BPM，水平和垂直各6块校正磁铁用于束流轨道校正，校正后的轨道满足束流传输要求。     

Reliability analysis of metal‐composite adhesive joints under debonding modes I,II, and I/II using the results of experimental and FEM analyses

In the present study, the experimental and finite element (FE) analyses are first carried out to investigate the deboning behavior of metal‐composite adhesive joints under modes of I and mode II loading. To conduct an FE on the debonding propagation, cohesive zone method (CZM), as well as maximum nominal stress and energy criteria, is applied. In the reliability analysis, to achieve the probability of debonding growth (PODG), limit state functions are formulated based on the energy release rate. To that end, the first‐order reliability method (FORM), the second‐order reliability method (SORM), and the Monte Carlo simulation (MCS) are used to calculate the PODG. The effect of initial debonding length on the PODG in all mentioned modes is investigated. Results obtained from reliability analysis reveal that the random variables including the initial debonding length, width, and thickness are the most sensitive variables to ascertain the PODG.     

Polypyrrole and platinum deposited onto carbon substrate to enhance direct methanol fuel cell electrodes behaviour

The aim of this work is to study the ability of polypyrrole to reduce the platinum load of low temperature methanol fuel cell electrodes. Platinum was deposited onto carbon paper and a layer of polypyrrole electrodeposited onto carbon paper, using electron beam evaporation and electrodeposition by pulses. Subsequently, the morphology and electrochemical behaviour of the synthesised samples were analysed in sulphuric acid solution, determining their electrochemically active surface area; and in a solution of sulphuric acid and methanol, to analyse their catalytic performance. The electrochemical measurements showed that the electrochemically active surface area and the catalytic performance of the electrodes prepared by evaporating platinum are increased when prepared on the polypyrrole film. Electrodes prepared using the pulse electrodeposition technique presented fairly homogeneous coatings that led to the reduction of the oxidation potential of methanol and the increase of their resistance to CO poisoning.     

Estimation of anisotropic properties of nano-structured arrays by modal vibration control at microscale

Nano-structured arrays are engineered to meet the requirements of a variety of applications such as microfilters, sensors, and structural interface due to their unique mechanical characteristics, which cannot be achieved by conventional solid materials. However, it is hard to evaluate the elastic properties of nano-structured arrays owing to the discrete structure, sample size, and availability of suitable techniques. To facilitate this, we develop an advanced three-dimensional microscale vibration testing process. In the test, a specially designed three-dimensional microspecimen with tuned mass is excited by a piezoelectric actuator, and the resonance frequencies are detected by a laser device successfully. The anisotropic elastic moduli of nano-structured array composed of helical nano-springs are identified from a single spectrum. This array shows so strong characteristic anisotropy that the solid one hardly can attain. The microscale testing technique can be extended to other materials and microstructures.     

Free vibration behavior of a thermally post-buckled FG Timoshenko beam under large deflection using a tangent stiffness-based method

For thermally postbuckled configurations, the free vibration behavior of functionally graded (FG) Timoshenko beams are investigated. The postbuckling configurations are obtained through a geometrically nonlinear static problem. The free vibration problem around the postbuckled configuration is formulated using its tangent stiffness. The energy based governing equations are solved following the Ritz method. The elements of the tangent stiffness matrix are obtained using the Ritz coefficients. The results are shown to exhibit the effects of FG material, material profile parameter, and length-thickness ratio. The comparative results are presented for both the cases of the physical neutral surface and the geometrical neutral surface.